Bluetooth-Modul

http://mc.mikrocontroller.com/images/deu.gif Seite in deutsch

http://mikrokopter.de/images/fra.gif Page en français

Shoplink

SET: Bluetooth-Module F2M03GXA + BT-Adapter + Parts: Shoplink

Bluetooth Adapter V1.0 (BT-AP)

BT-AP10/BT-AP10_.jpg

The board works as a power supply and level adjustment for the Bluetooth Module F2M03GXA.
This means that the BT module can be operated on a microcontroller with a 5V supply.
For an easier configuration the direction of RxD & TxD can be changed with solder jumper.

Instructions regarding the start up

/!\ To avoid (self-inflicted) damages at the BT-Module necessarily proceed as follows:

- First at all assemble the BT-Adapter PCB.
- Solder only the connection to the Bluetooth-Module if you have verified the correct function of the circuit.

Connect the BT-Adapter over a ribbon cable to the FlightCtrl.
It's enough if only the contacts #2 (+5V) and #7 (GND) been soldered.
For that reason you can use also the bigger pads.
The LED must flash and between the pins BT36 & BT37 you should measure 3,3V.
(See Schematic and assembly)

If that is OK you can solder the adapter to the module.

Assembly Bluetooth-Adapter and Bluetooth-Module

The very thin PCB-board (only 0,3mm) will be simply soldered to the bottom of the Bluetooth-Module.

/!\ ATTENTION: Tantal capacitors have the mark at the anode (+). "marking=anode" is also described in the PDF-File of the Elkos.
BT-AP10/BT_Photo1.jpg

Tipp:
To connect the adapter board with the module you can use also single strands of a cable.


To the pins 1-10 (necessary are only the pins 1;2;7;9) you can solder very simple the ribbon cable:
BT-AP10/BT_Photo2Ka.jpg

The ribbon cable should be connected as shown.
If you connect it to the other side you disturb the Bluetooth antenna and also the receiving.




Connection to the Flight-Ctrl

You need to set the solder jumper as follows:

BT-AP10/BT_JP_FC.jpg

Jumper

  • S1: 1-2
  • S2: 2-3



The complete Bluetooth-Module will be connected to the 10pin connector at the FlightCtrl.

BT-AP10/BT_FC.jpg


{i} If you use the GPS-System the module will be connected to the "Debug"-Port of the NaviCtrl .

Connecting to the PC

You need to set the solder jumper as follows:
BT-AP10/BT_JP_CFG.jpg

Jumper

  • S1: 2-3
  • S2: 1-2

Connecting to the MKUSB

The complete Bluetooth-Module will be connected to the MK-USB.
The jumper on the MK-USB need to be closed to supply the Bluetooth-Module with power.

http://gallery.mikrokopter.de/main.php/v/tech/BT_MKUSB.jpg.html

Connecting to the SerCon

Who still uses a Sercon can do this also.
Here you need to supply power to the PCB over the displayed spots +5V (red cable) and GND (black cable).

BT-AP10/BT_PhotoSercon.jpg

Schematic

BT-AP10/BT-SCH_kl.gif

BT-AP10/Bluetooth-Adapter-PCB_V10_sch.pdf

Layout of placement

BT-AP10/BT-BST.gif BT-AP10/BT-BST2.gif

BT-AP10/Bluetooth-Adapter-Platine_V10_brd.pdf

Configuration

(!) NOTE The Bluetooth-Modules out of our shop are already programmed and tested.

The settings are:

  • Device Name: MikroKopter_BT

  • Password: 0000

  • Baud: 57600

  • Slave (for the connection to the MikroKopter)



After a successful assembly the Bluetooth-Module can be detected with those datas over a PC/Laptop or a cellphone with Bluetooth.

If you want to use two Bluetooth modules to get a greater range a second Bluetooth module need to be connected to the MK-USB.
(The manufacturer declares for the Bluetooth module F2M03GXA a range of ~350 mtr.)

Two settings for the Bluetooth Module need to be changed on the PC-side:

  • The solder jumper need to be changed.
  • The module need to be set to Master .

With those settings you can pair both Bluetooth Modules with a secure connection.

Pairing two Bluetooth Modules

Two BT-Modules can be easily combined with each other via the configuration tool (pairen).

This can be done with the program "Free2move Configuration Software" Download

Step by Step Instruction:

  • Connect Bluetooth-Modul to FlightControl (solder jumper on BT Adapter: S1:1-2 / S2:2-3)

  • Connect Bluetooth-Modul to MK-USB (place jumper on MK-USB, solder jumper on BT Adapter: S1:2-3 / S2:1-2)

  • Open program "Free2move Configuration Software" .

  • Choose COM Port from MK-USB and click "OK" .


  • Example View:
    BT-AP10/usb1.jpg



  • Once the module has been detected the program opens.


  • Example View:
    BT-AP10/usb2.jpg



  • Now you click on the tab "Connection".

  • Change "Device Mode:" now to "Connecting (master)" and than click on "Find device..." .


  • Example View:
    http://gallery.mikrokopter.de/main.php?g2_view=core.DownloadItem&g2_itemId=78057&g2_serialNumber=2



  • Place a checkmark at "Enable Remote Name Request" and click on "Search" on the right.
  • In the window below all accessible Bluetooth connections are listed.
  • Click on the Bluetooth-Module of the Kopter and click "OK" .


  • Example View:
    BT-AP10/usb4.jpg



  • Now the "Bluetooth address" will be displayed right below.
  • Finish all by clicking on "Write Configuration" .


  • Example View:
    BT-AP10/usb5.jpg



  • READY



If you open now the KopterTool a connection between both Bluetooth-Modules should be established and the transferred datas been displayed.


Link

see also: Do-it-yourself solution: BTAP


  • KategorieMK-Baugruppe/de